Endcuts for Asymmetrical T-bars (Profile Type 35)

In most cases the end cuts for L-bars may be used also for asymmetrical T-bars that are close to L-bars (that means, where the flange only slightly extends outside the web on the mould side of the profile). However, in certain cases neither the endcuts for L-bars nor T-bars are appropriate. This paragraph contains some endcut types that are specific for asymmetric T-bars.

Type 40:

Remarks:

1. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web

2. a 4 is by default 90 degrees. Any given value will override this default value.

   Code, parameters	R1	a2	a3
   4001, b, c[, a1, a4] 4002, b, c[, a1, a4] 4011, b, c[, a1, a4]	0 0 35	30 30 30	30 18 30
   4012, b, c[, a1, a4] 4031, b, c[, a1, a4] 4032, b, c[, a1, a4]	35 75 75	30 30 30	18 30 18
   4041, b, c[, a1, a4] 4042, b, c[, a1, a4]	60 60	30 30	30 18

Type 41:

Remarks:

3. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (larger than half the flange width) on the mould line side of the web.

4. a 4 is by default 90 degrees. Any given value will override this default value.

Code, parameters	R1	a2	a3
4101, b, c[, a1, a4] 4102, b, c[, a1, a4] 4111, b, c[, a1, a4]	0 0 35	30 30 30	30 18 30
4112, b, c[, a1, a4] 4131, b, c[, a1, a4] 4132, b, c[, a1, a4]	35 75 75	30 30 30	18 30 18
4141, b, c[, a1, a4] 4142, b, c[, a1, a4]	60 60	30 30	30 18

Type 42:

Remarks:

5. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web

6. a 4 is by default 90 degrees. Any given value will override this default value.

Code, parameters	R1	a2
4201, c[, a1, a4] 4211, c[, a1, a4] 4231, c[, a1, a4] 4241, c[, a1, a4]	0 35 75 60	30 30 30 30

Type 43:

Remarks:

7. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (larger than half the flange width) on the mould line side of the web.

8. a 4 is by default 90 degrees. Any given value will override this default value

.

Type 132:

Remarks:

9. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

10. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	a2
13201, b[,c, a1, a4] 13202, b[,c, a1, a4] 13203, b[,c, a1, a4]	35 35 35	18 30 45

Type 133:

Remarks:

11. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

12. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	a2
13301, a, b[,c, a1, a4] 13302, a, b[,c, a1, a4] 13303, a, b[,c, a1, a4]	35 35 35	18 30 45

Type 134:

Remarks:

13. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

14. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (larger than half the flange width) on the mould line side of the web.

Code, parameters	R1	a2
13401, b[,c, a1, a4] 13402, b[,c, a1, a4] 13403, b[,c, a1, a4]	35 35 35	18 30 45

Type 135:

Remarks:

15. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

16. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (larger than half the flange width) on the mould line side of the web.

Code, parameters	R1	a2
13501, a, b[,c, a1,a4] 13502, a, b[,c, a1, a4] 13503, a, b[, c, a1, a4]	35 35 35	18 30 45

Type 136:

Remarks:

17. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

18. The small sketch to the right shows how a small notch may be defined below the end of the flange

19. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
13601, b[,c, a1, a4] 13602, b[,c, a1, a4] 13603, b[, c, a1, a4]	35 35 35	55012 55012 55012	18 30 45

Type 137:

Remarks:

20. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

21. The small sketch to the right shows how a small notch may be defined below the end of the flange.

22. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, designation	R1	R2	a2
13701, a, b[,c, a1, a4] 13702, a, b[,c, a1, a4] 13703, a, b[, c, a1, a4]	35 35 35	55012 55012 55012	18 30 45

Type 138:

Remarks:

23. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

24. The small sketch to the right shows how a small notch may be defined below the end of the flange.

25. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
13801, b[,c, a1, a4] 13802, b[,c, a1, a4] 13803, b[, c, a1, a4]	35 35 35	55012 55012 55012	18 30 45

Type 139:

Remarks:

26. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

27. The small sketch to the right shows how a small notch may be defined below the end of the flange.

28. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
13901, a, b[,c, a1, a4] 13902, a, b[,c, a1, a4] 13903, a, b[, c, a1, a4]	35 35 35	55012 55012 55012	18 30 45

Type 153:

Remarks:

29. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

30. The small sketch to the left shows the parameters of the corner notch.

31. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
15301, a, b[,c, a1, a4] 15302, a, b[,c, a1, a4] 15303, a, b[, c, a1, a4]	50 50 50	25 25 25	18 30 45

Type 157:

Remarks:

32. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

33. The small sketch to the left shows the parameters of the corner notch.

34. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (more than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
15701, a, b[,c, a1, a4] 15702, a, b[,c, a1, a4] 15703, a, b[, c, a1, a4]	50 50 50	25 25 25	18 30 45

Type 160:

Remarks:

35. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

36. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
16001, b[,c, a1, a4] 16002, b[,c, a1, a4] 16003, b[, c, a1, a4] 16004, b[,c, a1, a4]	35 35 35 35	0 0 0 KS10	18 30 45 18

Type 161:

Remarks:

37. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

38. The small sketch to the left shows the parameters of the corner notch.

39. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
16110, a, b[,c, a1, a4] 16120, a, b[,c, a1, a4] 16130, a, b[, c, a1, a4]	35 50 60	0 10 KS10	18 30 45

Type 162:

Remarks:

40. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

41. The small sketch to the left shows the parameters of the corner notch.

42. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively small "overshoot" of the flange (less than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
16201, a, b[,c,a1, a4] 16202, a, b[,c, a1, a4] 16203, a, b[, c, a1, a4]	50 50 50	25 25 25	18 30 45

Type 163:

Remarks:

43. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

44. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (more than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
16301, b[,c, a1, a4] 16302, b[,c, a1, a4] 16303, b[, c, a1, a4] 16304, b[, c, a1, a4]	35 35 35 35	0 0 0 KS10	18 30 45 18

Type 164:

Remarks:

45. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

46. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (more than half the flange width) on the mould line side of the web.

Code, parameters	R1	R1	a2
16401, a, b[,c, a1, a4] 16402, a, b[,c, a1, a4] 16403, a, b[, c, a1, a4] 16404, a, b[, c, a1, a4]	35 35 35 35	0 0 0 10	18 30 45 18

Type 165:

Remarks:

47. If c is not given (or =0), c will be set equal to the flange width a2 will become irrelevant and the flange angle will be set to a4.

48. The small sketch to the left shows the parameters of the corner notch.

49. This endcut type is intended for asymmetric T-bars (profile type 35) with a comparatively large "overshoot" of the flange (more than half the flange width) on the mould line side of the web.

Code, parameters	R1	R2	a2
16501, a, b[,c, a1,a4] 16502, a, b[,c, a1, a4] 16503, a, b[, c, a1, a4]	50 50 50	25 25 25	18 30 45

Type 167:

Remark:

If be equals the profile height aplha3 will be set to 90 deg.