Dragging Equipment and Nozzles
- Last UpdatedNov 18, 2025
- 3 minute read
Keywords:
DRAG AT BY POSITION MOVE
Description:
This command repositions the current element and constrained network to the specified position. The DRAG command can be followed by any standard Equipment and Civils positioning or moving command.
|
Examples: |
|
|---|---|
|
DRAG AT X3000 |
The current element and constrained network will be dragged to the specified position. |
|
DRAG BY Y500 Z500 |
The current element and constrained network will be dragged by the specified amount. |
|
DRAG MOVE X2000 |
The current element and constrained network will be moved to the specified position. |
|
DRAG MOVE YN CLEAR 1000 INF /BUILD10 |
The current element and constrained network are moved North to the specified clearance in front of element /BUILD10. |
Command Syntax:
The full DRAG command syntax is extensive but may be summarized as follows:
>-- DRAG --+-- <absol> --.
| |
‘-- <relat> --+-->
where:
<absol>
defines any absolute positioning command, for example, AT, POS,
<relat>
defines any relative positioning command, for example, BY, MOVE,
The full expanded syntax is given below for reference:
<absol> = >--+-- AT --+-- <bpos> ---.
| | |
| ‘-- <polar> --|
| |
|-- <pppos> --. |
| | |
‘-- <polar> --+--------+-->
<polar> = >--+-- POLar <bdir> --.
| |
‘-------------------+-- <plane> -->
<pppos> = >-- POSition --+-- <marke> --+-- AT --+-- <bpos> ---.
| | | |
| | ‘-- <polar> --|
| | |
| ‘-- <polar> -----------|
| |
|-- AT --. |
| | |
‘--------+-- <bpos> ---. |
| | |
‘-- <polar> --+-------------+-->
<plane> = >-+- PLAne <bdir> -+- DISTance <uval> -+- <repla> ------.
| | | |
| | ‘----------------|
| | |
| |- <repla> --------------------------|
| | |
| |- THRough <bpos> -------------------|
| | |
| ‘- CLEArance -+- <uval> -. |
| | | |
| ‘----------+- <repla> -|
| | |
| |- <planf> -|
| | |
| ‘-----------|
|- DISTance - <uval> -+- <repla> -. |
| | | |
| |- <planf> -| |
| | | |
| ‘-----------+-------------------|
| |
|- CLEArance -+- <uval> -. |
| | | |
| ‘----------+- <repla> -. |
| | | |
| |- <planf> -| |
| | | |
| ‘-----------+----------------|
| |
|- <repla> -------------------------------------------|
| |
|- THRough <bpos> ------------------------------------|
| |
‘- <planf> -------------------------------------------+>
<repla> = >--+-- INFront --.
| |
|-- BEHind ---+-- <sgid> ---.
| | |
| |-- <marke> --|
| | |
| ‘-- <bpos> ---|
| |
|-- FROm --. |
| | |
‘-- TO ----+-- <bpos> ------+-->
<planf> = >--+-- ONTop --.
| |
‘-- UNDer --+-- <sgid> ---.
| |
|-- <marke> --|
| |
‘-- <bpos> ---+-->
<relat> = >--+-- BY <pos> --+-- WRT --.
| | |
| |-- IN ---+-- <sgid> --.
| | |
| ‘----------------------|
| |
‘-- <relmo> --------------------------+-->
<relmo> = >- MOVe -+- <marke> -+- ALOng -.
| | |
| |---------+- <bdir> <plane> ----.
| | |
| |- BY <pos> -+- WRT -. |
| | | | |
| | ‘- IN --+- <sgid> -|
| | |
| ‘- <plane> ---------------------|
| |
|- ALOng -. |
| | |
|---------+- <bdir> <plane> ----------------|
| |
|- BY - <pos> -+- WRT -. |
| | | |
| ‘- IN --+- <sgid> -----------|
| |
‘-- <plane> --------------------------------+->
Figure 3:32. Dragging Equipment and Nozzles by a specified amount
Figure 3:33. Dragging Equipment and Nozzles to a specified position
Figure 3:34. Dragging Equipment and Nozzles to a specified position